Soot, smoke and char removed by a licensed crew

Electrical Fire Cleanup in PACOIMA, California

Electrical Fire Cleanup in PACOIMA, California starts with cutting the hazard and ends with a home you can live in again. We pull charred wiring, contain soot before it travels, and run HEPA air scrubbers until the air tests clean. Whether a breaker panel cooked off in a San Fernando Gardens apartment or a wall outlet smoked up a Hansen Hills house, we handle the cleanup and the electrical fire damage restoration PACOIMA California homeowners call us for.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Fire Damage Restoration Pacoima — your local Fire Damage Restoration team
Careful work. Honest options.
About this service

What Electrical Fire Cleanup in PACOIMA, California Covers

Electrical Fire Cleanup in PACOIMA, California is the removal of soot, char, smoke residue and contaminated materials left behind after a wiring, outlet, panel or appliance fire. It is not a wipe-down. We open the wall cavity, pull melted electrical wiring and burned insulation, treat framing with char removal chemicals, and seal what stays with an encapsulant sealant so odor cannot bleed back through the drywall. Every job starts with an IR thermal camera scan to find hot spots the eye misses.

Most electrical fires in this city start small and hide: a bedroom outlet arcing behind furniture, a kitchen circuit overloaded by a space heater, a panel in a 1950s Pacoima Village bungalow that never got upgraded. By the time you smell it, soot has already ridden the HVAC system into every room. That is why we treat smoke odor lingering in HVAC systems as a separate problem, not an afterthought, and why we quote affordable electrical fire cleanup in PACOIMA California by the room, not by the hour.

  • ✓ Soot Stopped at the Source
  • ✓ Air Tested, Not Guessed
  • ✓ Insurance Paperwork Handled
  • ✓ Same-Day Board-Up and Power Isolation
What's included

What Electrical Fire Cleanup Includes

Every electrical fire cleanup includes the core work: stabilization, damage mapping, char and soot removal, odor treatment and clearance documentation. What changes job to job is how far the smoke traveled and whether wall cavities have to be opened. We tell you which category your job falls into before we start, and we put the scope in writing.

✓

Emergency Board-Up and Containment

We isolate the failed circuit, board or tarp any opening, and set plastic containment so soot stops moving through the house. This happens the same day we arrive, typically within 60 to 90 minutes of walking in.

✓

Thermal and Boroscope Inspection

An IR thermal camera finds hot spots and hidden char inside wall cavities. A boroscope inspection camera lets us look inside those cavities without opening every wall. Both feed the written scope and the insurance file.

✓

Char and Melted Wiring Removal

Charred framing, melted electrical wiring and burned insulation come out and get bagged in the room. We do not drag debris through clean hallways. Dry ice blasting equipment lifts soot off framing that stays.

✓

Soot Cleaning and Surface Treatment

Chemical sponges and soot sponges lift dry soot first, then we wet-clean. Walls, ceilings, cabinets and contents all get treated. What stays gets sealed with an encapsulant sealant so odor cannot bleed back through the paint.

✓

Odor and Air Quality Treatment

A thermal fogger pushes odour counteractant into the same crevices the smoke reached. Ozone generators and hydroxyl generators run in unoccupied cycles, and HEPA air scrubbers run continuously. We verify with a particle counter before we pull containment.

✓

Documentation and Clearance

You get photo documentation, moisture logs and a written clearance summary formatted for your adjuster. If reconstruction is needed, we hand off the scope so nothing falls between the cleanup crew and the rebuild crew.

How it works

How Our Electrical Fire Cleanup Process Runs

01

Emergency Stabilization

We arrive, confirm the circuit is dead, and isolate it at the panel. Then we board windows, tarp roof openings and set containment plastic so soot stops migrating. On a typical PACOIMA call this takes 60 to 90 minutes, and you get a written scope before demolition starts.

02

Damage Mapping

An IR thermal camera and a boroscope inspection camera let us see inside wall cavities without tearing everything open. We mark every charred stud, every smoke-stained joist, and every wet zone from firefighting water. This map drives the estimate and the insurance claim.

03

Char and Soot Removal

Melted electrical wiring, burned insulation and charred framing come out first. We bag debris in the room, not through the house. Then dry ice blasting equipment lifts soot off framing and masonry without the grit that soda blasting leaves behind. Walls get chemical sponges, ceilings get soot sponges.

04

Odor and Air Treatment

A thermal fogger pushes odour counteractant into the same crevices smoke reached. Ozone generators and hydroxyl generators run in unoccupied cycles to break down the rest. HEPA air scrubbers run the whole time. We do not call it done until the air reads clean on a particle counter.

05

Clearance and Handoff

We pull the containment, wipe down hard surfaces one last time, and walk you through the finished space. You get photo documentation, moisture logs and a written clearance summary for your adjuster. If reconstruction is needed, we hand off the scope so nothing gets lost between trades.

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

IR Thermal Camera

Finds hot spots and hidden char inside wall cavities without opening every wall. It is the first tool on site and the one that drives the scope.

Boroscope Inspection Camera

Lets us look inside cavities, ductwork and attic spaces before we close them. Nothing gets sealed in without being seen first.

Dry Ice Blasting Equipment

Lifts soot off framing and masonry without the grit that soda blasting leaves behind. No secondary cleanup, no residue in the cavity.

Thermal Fogger

Pushes odour counteractant into the same crevices the smoke reached. Surface spraying does not get there. Fogging does.

Hydroxyl Generator

Breaks down smoke odor in occupied-adjacent spaces. We run it alongside HEPA air scrubbers for continuous treatment during the day.

HEPA Air Scrubber

Filters fine soot particles out of the air continuously. On a 1,200-square-foot house we run 24 to 48 hours before we verify with a particle counter.

Moisture Meter and Dehumidifier

Firefighting water hides in subfloor and insulation. We read it daily and dry it out before mold gets a foothold.

Real results

Before and after.

Bedroom Outlet Fire, Pacoima Civic Center

Before

An outlet behind a dresser arced and burned a 3-foot section of wall. Soot traveled up to the ceiling and across two closets. The breaker tripped, but the smell was through the whole room and the hallway.

After

Wall opened, charred stud and wiring removed, cavity cleaned and sealed. Ceiling and closets cleaned with chemical sponges. Air scrubbers ran 36 hours. Particle counts returned to pre-fire baseline.

Panel Fire, San Fernando Gardens Duplex

Before

A panel fire in one unit filled the shared hallway with smoke. Two units affected, one shared meter. The landlord needed documentation that separated the two units for the claim.

After

Panel area cleared, charred material removed, both units cleaned and treated separately. Hallway fogged and aired. Documentation split by unit. Odor gone in three days.

Attic Wiring Fire, Hansen Hills

Before

Attic wiring smoldered for hours before the smell reached the living space. Charred insulation and two burned joists. Smoke had settled into the attic insulation across a 400-square-foot area.

After

Charred insulation and lumber removed. Attic cleaned and treated with hydroxyl generators. Roof structure documented for repair. Air tested clean before insulation was replaced.

Problems we solve

Problems We Solve After an Electrical Fire

The fire is out. The problems are just starting. Here are the four we see most often in PACOIMA, and what each one costs you if it gets ignored.

Ask a pro →
01

Smoke odor that keeps coming back

We treat the source, not the air. Thermal fogging, ozone treatment and hydroxyl generators run in sequence, and we verify with a particle counter before we call it done. If the HVAC is contaminated, we fog the ducts too.

↗
02

Soot staining that sets permanently

We dry-sponge first with chemical sponges and soot sponges, then wet-clean. That order matters. It is the difference between cleaning a wall and replacing it.

↗
03

Hidden char inside wall cavities

An IR thermal camera and a boroscope inspection camera let us see inside the cavity before we close it. Anything charred comes out. Anything that stays gets sealed and documented.

↗
04

Water damage from firefighting

We dry the structure with air movers and dehumidifiers while we clean the soot. Moisture meter readings go in the file daily until the structure reads dry.

↗
Proof you can check

Licensed, Certified and Documented

✓
IICRC Fire and Smoke Restoration Technician (FSRT)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC Odor Control Technician (OCT)Institute of Inspection, Cleaning and Restoration Certification
✓
EPA Lead-Safe Certified FirmU.S. Environmental Protection Agency
✓
OSHA 10-Hour Construction SafetyOccupational Safety and Health Administration
✓
California Contractors State License Board (CSLB) LicensedCalifornia Contractors State License Board
Good questions

Frequently Asked Questions

(833) 929-6186 →

Most residential electrical fire cleanups in PACOIMA run $1,800 to $6,500 in 2026, depending on how many rooms the soot reached and whether wall cavities have to be opened. A single-room outlet fire with light smoke damage sits at the low end. A panel fire that pushed smoke through the HVAC system lands at the high end. We give you a written range after the damage mapping walk-through, before any demolition.

We do, and we are local. Fire Damage Restoration Pacoima handles electrical fire damage restoration in PACOIMA California, including char removal, soot cleaning, odor treatment and documentation for your claim. We have been serving this city since 2024 and we cover every neighborhood from Pacoima Civic Center to the Terra Bella Street Area. Call (833) 929-6186 and we will schedule a walk-through.

Yes, in most cases. A standard California homeowners policy covers fire damage from an electrical cause, including cleanup, odor treatment and reconstruction. What it will not cover is the failed wiring itself if it was a maintenance issue. We document cause and damage separately so your adjuster can see the difference, which is the single biggest factor in getting a clean approval.

No. Do not re-energize a circuit that has been through a fire until a licensed electrician has inspected it. Arced wiring can look intact and still fail. We isolate and tag the failed circuit when we arrive, and we do not restore power to it. The circuit stays off until the electrician signs off, and then we finish the cleanup around the repaired work.

Ready when you are

Get Electrical Fire Cleanup in PACOIMA, California Today

Every hour you wait, soot settles deeper and the odor gets harder to pull out. Call (833) 929-6186 and we will schedule a walk-through, give you a written scope, and start the same day if the damage is active. Licensed, insured and documented for your claim.

Call Now (833) 929-6186 →
Request an appointment

Get Fire Damage Restoration in PACOIMA

Call (833) 929-6186 any time, day or night. A live person answers, takes your address and gives you an arrival window. If you prefer email, send the details to info@firedamagerestorationpacoima.com and we will respond the same day. Emergencies get priority dispatch.

Request received — our team will be in touch shortly.
Tap to call(833) 929-6186